manualshive.com logo in svg

Labrie MINIMAX, Руководство по обслуживанию

Поделиться
Скачать
Labrie MINIMAX Скачать руководство пользователя страница 163

10

Lifting Arm

To keep the arm in good working order and to reduce 
the amount of down time and risk of accidents, a 
preventive maintenance program must be 
implemented and followed thoroughly.

Maintenance personnel must be familiar with 
operation of the arm, the safety around it and the 
maintenance procedures described in this chapter.

Daily Inspection

On a daily basis, perform a visual inspection of the arm, 
looking for leaks, cracks or premature wear of the 
moving parts. For detailed information on greasing 
points, see 

Lubrication

 on page 57.

To perform the daily inspection:

1.

Start the engine and engage the hydraulic pump 
(

PTO ON

).

2.

Fully extend the arm.

3.

Turn off the hydraulic pump and the engine.

4.

Perform a visual inspection of the following items:

Danger!

Always lock out and tag out the vehicle 
when inspecting or performing 
maintenance on it (see 

Locking Out and 

Tagging Out the Vehicle

 on page

 20).

Danger!

Do not stand directly in the path of the 
arm while performing the inspection.

Содержание MINIMAX















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды