LABORIE Nexam Pro WPU-L4 Скачать руководство пользователя страница 113

Страница: 113 / 278

Anorectal Manometry

Nexam Pro User Manual

113

9.2.2

Select the Catheter

Anorectal manometry investigations can be performed by either using (a)
water catheters with DT-NN pressure transducers, (b) air-charged catheters

with external pressure transducers or (c) solid state catheters. LABORIE
advises to use catheters with 4 pressure channels for the most accurate

results.

The layout of the two most common 4-channel catheters is displayed in

Figures 9.2 and 9.3:

•

one cm spacing between the four pressure channels (spiral) and a balloon

at the tip in order to test the anorectal reflex (RAIR) and sensations.

•

four pressure channels at the same location (radial) with an angle of 90

degrees and a balloon at the tip in order to test the anorectal reflex (RAIR)

and sensations.

Figure 9.2

Anorectal manometry catheter, spiral

Figure 9.3

Anorectal manometry catheter, radial

Содержание Nexam Pro WPU-L4























































































































































































































































































Результаты поиска

Содержание Nexam Pro WPU-L4

Отзывы:

Похожие инструкции для Nexam Pro WPU-L4

Бренды по названию

Популярные бренды

LABORIE Nexam Pro WPU-L4, Руководство пользователя

Результаты поиска

Содержание Nexam Pro WPU-L4

Отзывы:

Похожие инструкции для Nexam Pro WPU-L4

Бренды по названию

Популярные бренды