LABORIE Nexam Pro CIM Скачать руководство пользователя страница 37

Страница: 37 / 278

Investigation Procedure

Nexam Pro User Manual

the investigation protocol. The default is 150 cmH

O; the maximum setting is

200 cmH

2.5.5

Prepare the Combination Interface Module

The Combination Interface Module (CIM module) combines interfaces for
pressures, EMG and/or conductance in one housing. Depending on your

configuration, the module contains:

•

Lemo 4 connectors for reusable solid-state catheters, air-charged

catheters, or Sensonor/Memscap transducers with water catheters.

•

Argon (formerly B-D) connectors for DT-XX transducers with water

catheters.

•

Holders for DT-XX or Memscap (formerly Sensonor) pressure transducers.

•

Lemo 3 connector for conductance/leakage channel.

•

DIN connector for EMG cable.

•

Ground reference safety connection.

Figure 2.17

CIM module for solid-state/air-charged/Memscap transducers

Lemo 4 pressure transducer connectors

Connector for cable to U2M module

No longer available

Ground reference

EMG 6-pole DIN connector

Holder for Memscap transducers

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды