LABORIE Nexam Pro CIM Скачать руководство пользователя страница 127

Страница: 127 / 278

Anorectal Manometry

Nexam Pro User Manual

127

The procedure to prepare the investigation is as follows:

▪

Put the DT-NN pressure transducers in the holder and connect the

transducers to the CIM module.

▪

Install a bag with distilled water in the pressure-cuff.

▪

Put the spike of the 4-way catheter flushing set into the bag.

▪

Connect the 4-way catheter flushing set to the pressure transducers.

▪

Enter and select the

patient name

in the database program.

▪

Click the

New investigation

button in the database program.

▪

Click the

Anorectal manometry

button to start the pre-test.

▪

Place the pressure transducer holder at patient level.

▪

Connect the water catheter to the water transducers.

▪

Build up a pressure of 300 mmHg with the pressure-cuff.

▪

Open the clamp of the 4-way catheter flushing set to start perfusion.

▪

Flush the pressure transducers and catheter. Make sure that there are no

air bubbles left.

▪

Press the

Zero all after 10 seconds

button. Keep the catheter horizontal at

the level of the pressure transducers to zero all pressures.

▪

Move the catheter horizontally up to 30 cm above the pressure transducers.

Check the registration of the transducers by reading the pressure values.

▪

Insert the catheter gently in the anal canal of the patient and position the

balloon in the rectum.

▪

Ask the patient to cough to check the registration of the pressures.

▪

Press the

Start investigation

button to start the investigation. Follow the

procedure for the tests as described in the next paragraphs.

9.3.2

Air-Charged Catheters

The air-charged catheter is connected to the CIM module via air-charged
pressure transducer cables.

Figure 9.16

Air-charged catheter

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды