Before Starting Installation
- please study this instruction manual.
Make sure that you understand where each part needs to be located
and how they are connected together. Stages of Installation:
•
1. Plan the system layout
•
2. Run the cables
•
3. Fix and connect the Distribution Unit
•
4. Complete remote room installations
•
5. Fix and connect Base Unit
•
6. Commission and test the system.
Tools
- No special tools are required to install the Handylink PRO system, but you will need:
Screwdrivers (various sizes)
•
Drill and drill bit
•
Wire cutters and strippers (or knife for stripping)
•
Additional tools if cable is being run in walls or under floorboards, etc.
USER GUIDE
Introduction
Handylink Pro Kit - MRX270
4 + 1 distribution and remote control extender system
This MRX27O Handylink PRO kit contains the major parts that you need to install a professional TV and FM
radio distribution system in your home. The system is designed for distribution of DVD, VCR (‘video’) and
satellite receiver (‘Sky’) outputs as well as the usual TV channels. FM radio can also be distributed. Handylink
PRO is compatible with all UHF TV transmissions, including Channel 5 and digital terrestrial services, provided
that your aerial system is suitable. Handylink PRO replaces any TV distribution system already in place.
System Features
•
Up to four room outlets can be connected, in addition to the existing main TV (4+1).
•
Each of the additional outlets can be used for TV, FM or both.
•
All four outlets are enabled for remote control extension - This feature allows you to control your
VCR/DVD (or satellite receiver, etc.) from another room, using the normal remote handset.
•
Straightforward installation, fully explained in this manual.
•
Minimum ‘wiring clutter’ in the lounge.
•
Only one power point required.
HANDYLINK PRO Components
- what’s in the box?
Base Unit and Senders
The Base Unit is located near the VCR and
main TV in the lounge (it can be hidden if desired). It contains a
signal booster amplifier and the central system power supply.
The 3 Sender Buttons are fixed to the front of your DVD, VCR and
satellite unit and relay the infra red remote control commands.
Distribution Unit
The central wiring point for the four outlets, this contains a second
signal amplifier and has provision for connection of an FM radio aerial.
The Distribution Unit may be installed in any convenient location (e.g.
in the roof space or in a cupboard). No mains supply required.
4x Remote control receivers and 4x Couplers
These components can be used together on any outlet from the
distribution unit. They allow remote control of the VCR etc. from a
remote location (e.g. a bedroom) using the distribution system wiring.
Accessories
A fly lead is included for connection between the base unit and main
TV. What’s Not Included?Because everyone’s requirements are
different, this kit does not include coaxial cable, outlet plates or fly
leads for the TV or FM sets in the additional rooms. A satisfactory TV
aerial is required. If you also wish to distribute FM radio to the outlets
you will need an FM aerial.
Sender Buttons
Base Unit
Distribution
Unit
Remote
Control
Receivers
Couplers
Remote Control Extender Problems
Insert a recorded tape/DVD and select play to activate the VCR/DVD recorder. Set the main TV to the VCR/DVD
channel to display the ‘video’ picture. Get a helper to operate the VCR/DVD remote control handset in a remote
control equipped room (use play, pause, FF, etc.). The handset should be pointed toward the Infra-red Receiver and
your helper should see a green LED indicator flash on the Receiver when buttons are pressed. The green LED on the
Base Unit should also flash to show that the Sender is relaying commands from the remote room. You will probably
find that the VCR/DVD is already obeying the commands, but for continuing reliable operation the Sender button
should be attached to the front of the VCR using one of the sticky pads supplied. Before doing this, experiment with
the position of the Sender button to find the optimum position. (The buttons are transparent to infra-red and will
not interfere with normal operation of the VCR.) Repeat the test procedure and attach a Sender button for each
additional piece of equipment to be controlled. (In the remote room remember to set the TV to the appropriate
channel and use the correct handset!). Check that the remote control also works from any other rooms where you
have installed a receiver. If you later need to remove a Sender button, prise it gently away from the equipment.Your
Handylink PRO installation is now complete.
Installing the Handylink Pro System
Troubleshooting
Distribution System Problems
Symptom
Snowy’ pictures on all TV’s including the
main set/ or no digital Freeview™ signal
Snowy pictures on all TV’s including the
main set/ or no digital Freeview™ signal
’Snowy’ pictures/or no digital Freeview™
signal on one or more remote TV’s (but
others are OK)
Poor picture quality with faint image of
other channels in background
Patterning on satellite or ‘video’ pictures
Satellite or ‘video’ pictures not appearing
on remote TV’s
Off-air TV channels disappear (or ‘snowy’)
when VCR in playback mode
The problem may be
No power to Base Unit - Incorrect
connections to Base Unit
No power reaching Distribution unit (red
LED not alight)
Faulty cabling/connections to particular
room(s)
Very strong signals from aerial are over-
loading the amplifiers
Satellite and VCR tuned too close in
frequency (or close to off-air channel)
TV(s) not tuned-in to sat RF channels
VCR modulators disabled
(SCART connection used to main TV)
Some older VCRs do not pass off-air
channels whilst in play On some recent
models this feature is selectable in an
OSD menu
Solution
Check fuse, plug in and switch on! Check
your connections (see main diagram)
Check LINE connection between Base
Unit and Distribution Unit
Check connections between Distribution
Unit and room (s) in question
Fit a 12dB attenuator between aerial and
satellite receiver or VCR
Retune satellite and/or VCR (refer to
handbooks for (details)
Tune TV(s) in (refer to TV handbook)
Enable modulators - usually an OSD
menu option (refer to handbooks)
Old VCR: modify VCR (consult dealer) or
replace New VCR
Question
Is Receiver green light flickering even
when no remote control is being used?
Does Receiver green light flash when a
remote control handset is operated in
the remote room
Does base unit light also flash when a
remote control handset is operated?
The problem may be
Interference to the Receiver from
lights, e.g. compact fluorescents
On to next question
No mains connection to Base Unit
Faulty connections from
Distribution Unit to Coupler
Wrong type of TV wall socket in
remote room
Loose connection to Receiver
Direct sunlight falling on Receiver
On to next question
Sender is not plugged in correctly
/Sender wires cut or damaged
Sender buttons are not correctly
placed on controlled equipment
Solution
Move lamps and Receiver away from
each other
Check fuse, plug in and switch on!
Check wiring, see troubleshooting hints
Replace wall socket with non-isolated
type - see troubleshooting hints
Ensure Receiver is correctly plugged into
coupler
Move Receiver out of sunlight
Plug Sender into SENDER socket on Base
Unit Replace Sender (s)
Adjust position of Sender buttons
Ans.
Yes
No
No
Yes
No
Yes
Check Your Coaxial Plugs
- Check that the coaxial plugs on the cable run to the remote room are correctly fitted, as
shown in the diagram on page ?. The inner wire of the coax cable must be firmly connected in the centre pin of the
plug. On plugs without a clamping screw, this wire must be soldered.
Outlet Plates
- The Handylink PRO remote control extension facility will only work with non-isolated outlets. If you
have re-used wiring from an older distribution system, you will need to replace any isolated outlets.
This section is included mainly for professional installers wishing to comply with BS EN 50083-1. The Handylink PRO
system has provision for protective earth bonding. An earth terminal (capacity 6mm
2
) is provided at the
Distribution Unit since this is the central network star point’. For compliance with BS EN 50083-1 a minimum 4mm
2
bonding conductor is required from the main earth terminal of the electrical installation.
Fitted mains plug
- The Base Unit in this kit is supplied with a standard fused plug already fitted. If this is not
suitable, refer to the instructions below. In the unlikely event that you need to change the fuse in this plug, a 3 Amp
fuse to BS 1362 carrying the ASTA or BSI approval mark must be used. Always re-fit the plastic fuse carrier when
replacing the fuse.
Changing the plug
- If the fitted mains plug is not suitable for the socket outlets in your home, it should be cut off
and an appropriate new plug fitted.
Wiring a new plug
- Any instructions supplied with the new plug should be followed (these may state how much
insulation to remove from the wires in the mains cord). The brown wire must be connected to the live (L) terminal of
the plug and the blue wire to the neutral (N) terminal. Neither wire should be connected to the earth (E) terminal of
a 3-pin plug (this appliance does not require an earth connection). Ensure that the cord grip in the plug is correctly
used and clamps the sheath of the cord firmly. Fuse Rating: If the new plug is a fused type, the fuse fitted should be
rated at not more than 3 Amp.
CAUTION:
The old plug should be destroyed promptly since it would be dangerous if plugged into a live socket.
Your Handylink PRO distribution and remote control extender system is guaranteed against faulty components or
poor workmanship for a period of two years from the date of purchase.This guarantee does not cover accidental or
malicious damage (including damage from natural causes such as lightning) and will be invalidated by installation or
use other than in accordance with these instructions, repair or attempted repair other than by the manufacturer, or
opening or removal of the case.This does not affect your statutory rights as a consumer.
Troubleshooting
Earthing the system
Important safety advice
2 Year Guarantee
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority for recycling advice.
For further information or any queries please contact
Customer Careline: 08457 573 479
(Local rate – UK only)
Technical Support: http://technical.philex.com