Labcyte Echo 520 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 200

Labcyte Echo 520 Скачать руководство пользователя страница 49

Installation and Relocation

2-5

2.2

Installation overview

The Labcyte Echo liquid handler is installed by Labcyte field engineers. The
following is a brief overview of the hardware and software installation
steps they perform:

1.

Unpack the Echo liquid handler and place it in the area that meets the
minimum operating space requirement.

2.

Connect the Echo liquid handler to AC power, air pressure, vacuum
pressure, surge tank, coupling fluid bottle, and the coupling fluid chiller.

3.

Fill the coupling fluid bottle and prime the coupling fluid circuit.

4.

Perform a basic functional check of the Echo liquid handler.

5.

Perform the Site Acceptance Test (SAT) process (optional).

6.

Change the Echo IP address, if a different IP address is required by your
system administrator.

7.

Install the Echo software onto the customer-supplied PC
(client workstation).

8.

Connect the client PC to the Echo liquid handler and verify
communications.

Figure 2.2 Installed system

Ethernet cable

Compressed air line

Vacuum line

Client PC

Chiller

Echo liquid handler

fluid lines

Chiller

Bench

Floor

(cross-over)

Surge tank

«
...
47
48
49
50
51
...
»

Содержание Echo 520









































































































































































































Отзывы:

Нет отзывов