Labcyte Echo 520 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 200

Labcyte Echo 520 Скачать руководство пользователя страница 38

1-18

Echo Liquid Handler User Manual

1.4

What system configurations are supported?

The Echo liquid handler can be used in a manual configuration or in several
levels of automated, system integrated configurations. This section explores
the following operating modes:



Manual mode



Software-driven mode



Modular workstation mode



Small cell mode



Fully automated mode

The server/client architecture allows multiple client computers/programs to
connect to an Echo liquid handler at the same time. Read

“Multi-client

considerations” on page 1-23

for a discussion of the advantages and

disadvantages of multiple-client operation.

Note:

The software comes with a static IP address (192.168.1.1).

If this IP address is not available, or if you are installing more than one
Echo liquid handler on a network, use the Echo Admin Client (on the
Echo Server 2.4 disk) to change the IP address.

1.4.1 Manual operation

Manual operation

leaves control of every step to the operator:



Defining new fluid transfer protocols or new destination microplates



Executing a fluid transfer protocol



Loading and unloading both source and destination microplates



Monitoring status

Figure 1.13 Manual operation.

Manual operation is also used when performing the following functions:



Defining new destination microplates



Defining new fluid transfer protocols



Performing periodic maintenance and calibration

For more information about manual operation, read Chapter 4.

«
...
36
37
38
39
40
...
»

Содержание Echo 520









































































































































































































Отзывы:

Нет отзывов