Labconco Protector Echo Скачать руководство пользователя страница 39

Страница: 39 / 112

Connecting to your filtered hood

For connecting your phone or tablet to the filtered hood:

1. Open the network selector on your device.
2. Select the Wi-Fi network:

GFH-XXXXX-XXXX

(the

XXXX

is the serial number of the filtered hood).

3. Password is:

GFH-2018

4. Open an

internet browser (Google Chrome, Mozilla Firefox… etc.) and enter

the following address in the address menu:

http://192.168.1.1

For connecting the filtered hood to a laptop:

1. Connect an Ethernet cable to the laptop from the command module.
2. Select or type the following parameters:

a.  Protocol TCP/IP V4
b.  IP address: 192.168.0.206
c.  Subnet mask: 255.255.255.0

3. Open an

internet browser (Google Chrome, Mozilla Firefox… etc.) and enter

the following address in the address menu:

http://192.168.1.1

4. See Figure 6-3 for more details.

This will open a webpage that is the eGuard home screen.

Figure 6-3

Содержание Protector Echo

















































































































Результаты поиска

Содержание Protector Echo

Отзывы:

Похожие инструкции для Protector Echo

Бренды по названию

Популярные бренды

Labconco Protector Echo, Руководство пользователя

Результаты поиска

Содержание Protector Echo

Отзывы:

Похожие инструкции для Protector Echo

Бренды по названию

Популярные бренды