Labconco Logic+ A2 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 201

background image

86

Noise Test (optional)

The noise (sound pressure) should be measured as described in the current NSF/ANSI
Standard 49 Annex

F. To test the biosafety cabinet’s noise level, follow these

instructions:

1. Establish the sound meter location, as follows:

a.  On the left-to-right centerline of the biosafety cabinet
b.  14 inches (35.6 cm) above the work surface
c.  12 inches (30.5 cm) from the front of the biosafety cabinet

2.

With the biosafety cabinet’s blower(s) off, take a background reading with the
sound meter. It should be less than 55 dbA.

3. Start the blower(s) on the biosafety cabinet.

4. Place the sound meter at the location defined in Step 1, take a sound reading.

Acceptance Criteria

The noise (sound pressure) shall be no more than 67 dbA when the biosafety cabinet is
new, and no more than 73 dbA when the filters are loaded with particulate.

Vibration Test (optional)

The vibration level at the work surface should be measured as described in the current
NSF/ANSI Standard 49 Annex F

. To test the biosafety cabinet’s work surface vibration

level, follow these instructions:

Note:

The vibration meter must have a range of 20-20,000 Hz and provide an output in

displacement to proceed with this test.

1. Mark the geometric center of the work surface.

2. Place the vibration meter probe

at this point, and with the biosafety cabinet’s

blower(s) off, take a background reading.

3.

Start the biosafety cabinet’s blower(s). Wait 1 minute.

4. Take a reading at the same work surface location.

5. Subtract the reading with the blower(s) on from the background reading.

Acceptance Criteria

Net vibration shall be less than 0.0002 inches (5 x 10

-6

m) when the biosafety cabinet is

new.

«
...
84
85
86
87
88
...
»

Содержание Logic+ A2










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Logic+ A2

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: DARAY Страницы: 24

Бренд: Jafar Страницы: 9

Бренд: idiag Страницы: 12

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: Federal Signal Corporation Страницы: 12

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Бренд: B-K lighting Страницы: 2

Бренд: Dantel Страницы: 22

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 8

Бренд: Össur Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды