Labconco Logic+ A2 Скачать руководство пользователя страница 169

Страница: 169 / 201

169

Calibrate for Operation

After canopy installation, you MUST reconfigure the biosafety cabinet to have a canopy.

1. From the Home Screen, press the

[MENU]

button.

2. Press the

[DOWN]

button until the

Tools

option is

highlighted.

3. Press

[OK/MUTE]

to enter the menu screen.

4. Press the

[DOWN]

button until the

Password

option is

highlighted, then press

[OK/MUTE]

to select the

certifier’s submenus.

5. You will see a

Warning Screen

alerting you that you are

about to enter an area that can alter

the BSC’s settings;

Press

[OK/MUTE]

to input the password.

6. When requested for the password press:

[LIGHT]

[UV LIGHT]

[TIMER]

then

[OK/MUTE]

7. If the password is entered correctly, you can select

between altering the cabinet’s configuration, or
calibration. Highlight the

Configuration

option, then

press

[OK/MUTE]

to start the configuration procedure.

Содержание Logic+ A2










































































































































































































Результаты поиска

Содержание Logic+ A2

Отзывы:

Похожие инструкции для Logic+ A2

Бренды по названию

Популярные бренды

Labconco Logic+ A2, Техническое руководство

Результаты поиска

Содержание Logic+ A2

Отзывы:

Похожие инструкции для Logic+ A2

Бренды по названию

Популярные бренды