background image

5. Operation and performance 

20    

PLM+ SERIES Operation Manual  rev 3.0.1 

5.3.3. Power Average Limiter (PAL) 

The Power Average Limiter Active warning (PAL Active) will be displayed when the power supply’s maximum rated 

design parameters are reached. When this warning is displayed, gain limiting is being applied to the output signal 

and the ISVPL threshold is lowered accordingly.  

PAL activity is shown by flashing yellow on the frame LEDs and a corresponding text description on the front and 

in Lake Controller and CAFÉ software programs. Refer to section 9.1 for more information on warnings and faults. 

5.3.4. Breaker Emulation Limiter (BEL™) 

The BEL models the temperature in the external breaker and limits the mains current to prevent the breaker from 

• 

• 

 

  allows current above the threshold to pass for a short time, leading to an increased modeled temperature. For  

  the limiter to disengage, the current must reduce below the threshold to enable the breaker to cool down. 

• 

 

  momentarily allows current above the threshold for a longer time, leading to an increased modeled temperature. 

 

5.3.5. Under Voltage Limiter (UVL™) 

PLM+ devices are equipped with an under voltage limiter. With multiple, powerful devices on a mains distribution 

line, heavy current loads risk the reduction of voltage below that required for devices to function. The UVL reduces 

the mains current draw when voltage drops below 80 V. The amount of reduction applied increases as mains 

voltage drops towards 65 V; at 65 V the power supply is shut down. The mains supply is continually monitored and 

value can be set from 1 to 32 Arms, though the PLM 12K44 will automatically limit at between 5-25 and the 

PLM 5K44 between 2-15 Arms. Just as with ISVPL, the actual value is displayed in [ ]. The different models have 

different maximum current capabilities as specifies in the specification sheet. Also, the smaller models can be 

configured all the way up to maximum user range. When the nominal current is set above the model’s capabilities, 

the actual current is set to the maximum capabilities of the unit. Therefore, the nominal current can be set for the 

application and the configuration remains cross-compatible with all the models. There are three different profiles 

available for selection:

The BEL is configured manually from the front panel with the Lake Controller or CAFÉ software. CAFÉs ESP 

design aid can also predict the current consumption, with the exact speaker requirements, and propose a 

safeguarding BEL configuration 

BEL activity is shown by flashing yellow on the frame LEDs and a corresponding text description on the front panel, 

in Lake Controller and CAFÉ software programs. Refer to section 9.1 for more information on warnings and faults.

UVL activity is shown by flashing yellow on the frame LEDs and a corresponding text description on the front panel, 

in Lake Controller and CAFÉ software programs. Refer to section 9.1 for more information on warnings and faults.

Содержание PLM 20K44





























































































Отзывы: