A54-00001-60759
LUCIA Serial Dongle - RS-232
Quick Start Guide
General
This section describes general features of the LUCIA RS232
protocol. The LUCIA has the following features:
• Volume
control
• Mute
control
•
DSP Matrix control (and thereby source-selection)
• Status
readings
About the hardware
GND, TX and RX
The three connections compounds a regular RS232 interface.
GPO
GPO is directly linked to the Lucia amp’s GPO interface
(explained in the Lucia quick start guide).
Preparations
• In order to use the Serial Dongle the Lucia amp must be
updated to software rev:924 or higher.
• In the Lucia Application Browser the control port must be
setup to function RS232.
RS-232 Connection schematic
A RS-232 connection to a LUCIA unit can be established from a
computer via a USB Serial Adapter and a LAB.GRUPPEN Serial
Dongle as sketched below:
Communication Settings
The LUCIA uses 9600 bit/s, 8 databit, no parity and 1 stopbit.
Flow control (software or hardware) are not employed.
Command/Response
All commands/responses are in clear ASCII text and must be
terminated with a <CR> Carriage Return (0x0D).
Synchronization
A single <CR> can be used to empty the LUCIA command buff er
to synchronize further communications.
Unknown/Unsupported Commands
If the LUCIA receives an unknown command string, it will
respond with “ERROR UNKNOWN COMMAND”.
Visibility and persistence of settings
Parameters set through the RS-232 protocol are added on top
of the persistent settings of the LUCIA as set by the Application
Browser. Thus RS-232 infl icted settings are read with the
available RS-232 status polling commands and are not visible
through the Application Browser. The parameters set through
RS-232 remain when LUCIA enters and exits standby, but
only volume settings for RS-232 control persist when LUCIA
is powered down. Application Browser set settings persist
throughout the power cycle.
Controls
Step output volume up or
down
Command
stepvolume [output channels 1 to 4]
[+/- level in dB]<CR>
Function
description
Adjusts the output volume a number of
steps on the given channels. It is possible
to adjust the volume on multiple output
channels at once by using comma as
separator. The step level range is
-100 to 0 dB
. When the volume is at
-100 dB
the channel is considered muted.
The resolution of the volume control
is 0.5 dB
Usage
examples
One channel
stepvolume 1 -2
Multiple channels
stepvolume 1,2 -2
Returns
One channel
OK STEP VOLUME
CH1:-2
Multiple channels
OK STEP VOLUME
CH1:-4 CH2:-2
Error in parameters
ERROR STEP
VOLUME
Note:
The returned volume level is the
resulting volume level.
Note:
If multiple outputs are adjusted the
volume levels are only reported for
available outputs.
Set output volume to a specifi c level
Command
setvolume [output channels 1 to 4]
[level -100 to 0 dB] <CR>
Function
description
Adjusts the output volume to a specifi c
level for the given channels. It is possible
to adjust the volume on multiple output
channels at once by using comma as
separator. The level range is
-100 to 0 dB
.
When the volume is at
-100 dB
the channel
is considered muted. The resolution of the
volume control is 0.5 dB
Usage
examples
One channel
setvolume 1 0
Multiple channels
setvolume 1,2 -11.5
Returns
One channel
OK SET VOLUME
CH1:0
Multiple channels
OK STEP VOLUME
CH1:-11.5 CH2:-11.5
Error in parameters
ERROR STEP
VOLUME
Note:
If multiple outputs are adjusted the
volume levels are only reported for
available outputs.
Mute/Unmute all outputs
Command
setmute [state]<CR>
Function
description
Mutes or unmutes all outputs
Usage
examples
Mute all outputs
setmute 1
Unmute all outputs
setmute 0
Returns
Mute all outputs
OK MUTE 1
Unmute all outputs
OK MUTE 0
Error in outputs
ERROR MUTE
Set a matrix patch point gain
Command
setmtx [channel in][channel out]:[gain]...
<CR>
Function
description
Sets gain for one or more matrix patch
points. A patch point is specifi ed by input
and output channels concatenated without
separator. It is possible to set multiple patch
points in one go (see usage examples). The
gain range is
-31 to 0 dB
. When gain is at
-31 dB
the patch point is considered unset.
The resolution of the set gain is
0.5 dB
Usage
examples
Patch in1 to out1
setmtx 11:0
Patch multiple
channels
setmtx 11:0
12:-1 22:-2
Unset one patch
point
setmtx 11:-31
Returns
Patch in1 to out1
OK SETMTX 11:0
Patch multiple
OK SETMTX 11:0
12:-1 22:-2
Unset one patch point
OK SETMTX 11:-31
Error in parameters
ERROR SETMTX
Clear matrix and optionally set patch points gain
Command
clrmtx [channel in][channel out]:[gain]...
<CR>
Function
description
Clears the matrix (all patch point gains are
set to -31 dB), then sets the gain for one or
more specifi ed patch points. It is possible to
set multiple patch points in one go
(see usage examples). The gain range is
-31 to 0 dB
. When gain is at
-31 dB
the
patch point is considered unset.
The resolution of the gain is
0.5 dB
Serial Dongle
RS-232
Sub-D 9 female
(Looking at the pins
Pin Signal
5
3
2
5
1
6
9
GND
TXD
RXD
GPIO Port
GND
TX
RX
GPO
LUCIA
Controlling
Device
V2.0.1 09-25-2017
