L-Card L-502-P-G-D-I Скачать руководство пользователя страница 48

Страница: 48 / 73

Connection of signals.

4.6. Calculation of the total load power of L-502 output
circuits

If you intend to use L-502 output circuits to connect any external loads, then the total load

power should not exceed the power specified in the specification (see section

5.7

on p.

). The

load power should be estimated according to the procedure described below.

The total load power taken from the L-502 power system is:

where

is the total load power taken from digital DO outputs in the "1" state (only for

loads connected to the GND circuit);

— power load removed from the DAC outputs;

— power load, taken from the output of +15 V;

— power load, taken from the output of -15 V;

— power load, taken from the output of +3.3 V;

In turn, the power summands

of the corresponding i-th outputs must be calculated either

through the known load current

by the formula

, or through the known load

resistance

at the i-th output

The power summands

of the corresponding j-th outputs must be calculated either

through the known load current

by the formula

, or through the known load

resistance

at the j-th output

The power

and

should also be calculated either through known load currents

by formulas

or through a known load

resistance

, according to

formulas

All terms in the power formulas are positive, dimension: power — Watt, current — Ampere,

resistance — Ohm

Содержание L-502-P-G-D-I










































































Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды

L-Card L-502-P-G-D-I, Руководство пользователя

Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды