L-Card L-502-P-G-D-I Скачать руководство пользователя страница 15

Страница: 15 / 73

2.1: Configuration L-502.

2.1.2. The configuration of the outputs DAC1 and DAC2

3
4

No jumper on 3,4,5,6

The contact "DAC1" is not
connected to the external signal
connector, see item

4.2.1

, p.

Jumper on 3-4

The contact "DAC1" on the
connector is connected to the
DAC - channel 1

Jumper on 3-5

The contact "DAC1" on the
connector is connected to +15V

Jumper on 3-6

The contact "DAC1" on the
connector is connected to AGND

No jumper on 7,8,9,10

The contact "DAC2" is not
connected on the connector

Jumper on 7-8

The contact "DAC2" on the
connector is connected to the
DAC - channel 2

Jumper on 7-9

The contact "DAC2" on the
connector is connected to -15V.

Jumper on 7-10

The contact "DAC2" on the
connector is connected to the
DGND

digital ground

circuit.

2.1.3. Configuring the resolution of the active state of the digital outputs

For version 1 or 2 :

For version 3:

Jumper on 11-12

Forced output enable of the low-
order byte, see

4.2.3

, p.

36.

No jumper on
11-12

The resolution of the low byte
output depends on the program
setting.

Jumper on 13-14

Forced output enable of high
byte.

No jumper on
13-14

The output enable of the high
byte depends on the program
configuration.

Содержание L-502-P-G-D-I










































































Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды

L-Card L-502-P-G-D-I, Руководство пользователя

Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды