manualshive.com logo in svg

L-Acoustics SB18 IIi, Руководство пользователя

Поделиться
Скачать
L-Acoustics SB18 IIi Скачать руководство пользователя страница 23

Loudspeaker congurations

Loudspeaker congurations

SB18 IIi in standard conguration

Deployed in a standard conguration, an SB18 IIi system operates with an omnidirectional directivity pattern over the

nominal bandwidth of the SB18 IIi enclosure.
The [SB18_60] and [SB18_100] factory presets provide the subwoofer system with an upper frequency limit at 60 Hz

and 100 Hz respectively in order to optimize the acoustic coupling with a main full-range system.
The SB18 IIi subwoofer is driven by the  LA2Xi / LA4X / LA8 / LA12X  amplied controllers.

Reduced maximum SPL or drive capacity with LA2Xi: refer to the 

LA2Xi owner's manual

.

Preset

[SB18_60]

[SB18_100]

Low frequency limit (-10 dB)

32 Hz

Delay values

When combining a line source with subwoofers, delays may have to be added to the presets.
Refer to the Preset Guide to obtain the pre-alignment delay values.

SB18 IIi owner's manual (EN) version 1.0 

 23

Содержание SB18 IIi



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды