L-Acoustics S Series Скачать руководство пользователя страница 9

Страница: 9 / 80

System components

System components

Loudspeaker enclosures

Syva

2-way-passive enclosure: 6 x 5'' LF + 3 x 1.75'' HF diaphragm

Syva Low

High power low frequency subwoofer: 2 x 12'' LF

Syva Sub

Infra low frequency subwoofer: 1 x 12'' LF

Powering and driving system

LA2Xi / LA4X /

LA7.16i / LA12X

Amplied controller with DSP, preset library and networking capabilities

Refer to the LA2Xi / LA4X / LA7.16i / LA12X owner's manual for operating instructions.

Rack

LA-RAK II AVB

Touring rack containing three LA12X, LA-POWER II for power distribution, LA-PANEL II for audio

and network distribution, and two LS10 for AVB distribution

Cables

SP cables

SpeakON loudspeaker cables (4-point, 4 mm² gauge)
Come in different sizes: SP.7 (0.7 m / 2.3 ft), SP5 (5 m / 16.4 ft), SP10 (10 m / 32.8 ft), and

SP25 (25 m / 82 ft)

SP-Y1

Breakout cable for two passive enclosures (2.5 mm² gauge)
4-point speakON to 2 × 2-point speakON, provided with a CC4FP adapter

DO cables

PA-COM loudspeaker cables (8-point, 4 mm² gauge)
Come in different sizes: DO.7 (0.7 m / 2.3 ft), DO.10 (10 m / 32.8 ft), and DO.25 (25 m /

82 ft)

DOSUB-LA8

Breakout cable for four passive enclosures (4 mm² gauge)
8-point PA-COM to 4 × 2-point speakON

DOFILL-LA8

Breakout cable for two 2-way active enclosures (4 mm² gauge)
8-point PA-COM to 2 × 4-point speakON

DO3WFILL

Breakout cable for one 2-way active enclosure and two passive enclosures (4 mm² gauge)
8-point PA-COM to 1 × 4-point speakON and 2 × 2-point speakON

custom 2-point

speakON cable

2-point speakON cable (2.5 mm² gauge) to bare wire cable

This cable needs to be custom made.

2 × 2.5 mm² cable

speaker cable with bare wire endings
Adapt the cable length to the installation.

Information about the connection of the enclosures to the LA amplied controllers is given in

this document.

Refer to the LA2Xi / LA4X / LA7.16i / LA12X owner's manual for detailed instructions about the whole cabling

scheme, including modulation cables and network.

Rigging elements

Syva Wall

Wall-mount for Syva

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды