L-Acoustics S Series Скачать руководство пользователя страница 26

Страница: 26 / 80

Loudspeaker congurations

Syva colinear source with LF extension

In hybrid conguration with Syva Low, the Syva system bandwidth is extended down to 42 Hz and the system contour is

reinforced by 9 dB.
Syva and Syva Low are driven by the LA2Xi / LA4X / LA7.16i / LA12X amplied controllers.

Reduced maximum SPL or drive capacity with LA2Xi: refer to the

LA2Xi owner's manual

Coupled

The [SYVA LOW SYVA] hybrid preset enables acoustic coupling when Syva is on top of Syva Low (AutoConnect) or

within a 60 cm (24 in) distance.

To use [SYVA LOW SYVA], connect Syva and Syva Low to the same amplied controller output.

Use Autoconnect or an SP-Y1 cable. Refer to

Connection to LA amplied controllers

(p.53).

< 60 cm / 24 in

with AutoConnect

without AutoConnect

Enclosures

Syva

Syva Low

Preset

[SYVA LOW SYVA]

Frequency range (-10 dB)

42 Hz - 20 kHz

No pre-alignment delay values are required for the Syva system.

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды