L-Acoustics KARA II DOWNFILL FOR K1 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 24

background image

Rigging system description

Rigging system description

K1-BUMP

The K1-BUMP is designed to y K1 and/or K1-SB enclosure arrays. The K1-BUMP features one rack stabilizer to mount

up to four LA-RAK II AVB touring racks on the structure.

KARA-DOWNK1

KARA-DOWNK1 is a rigging interface for Kara II under a K1 array.
The four tabs on the top are compatible with the K1 rigging system.
The four slits tted with ball-locking pins accommodate the Kara II rigging arms.

slits and ball-locking pins (x4)

tab (x4)

Kara II downll for K1 addendum (EN) version 1.0

11

«
...
9
10
11
12
13
...
»

Содержание KARA II DOWNFILL FOR K1

























Отзывы:

Нет отзывов

Похожие инструкции для KARA II DOWNFILL FOR K1

Бренд: C SEED Страницы: 32

Бренд: Cambridge Audio Страницы: 4

PlayWorks PS2000 Digital

Бренд: Cambridge SoundWorks Страницы: 22

MegaWorks THX 2.1 250D

Бренд: Cambridge SoundWorks Страницы: 13

Center Channel II

Бренд: Cambridge SoundWorks Страницы: 7

Бренд: Cambridge SoundWorks Страницы: 14

Бренд: Cambridge Audio Страницы: 4

Бренд: d&b audiotechnik Страницы: 11

Бренд: JBL Страницы: 7

Бренд: Zagg Страницы: 21

Бренд: Mackie Страницы: 4

Бренд: Mackie Страницы: 12

Бренд: Yamaha Страницы: 17

Бренд: DAPAudio Страницы: 16

Бренд: Conquer Страницы: 2

Бренд: Turbosound Страницы: 8

Бренд: Vingtor Stentofon Страницы: 2

LP Series TO-3P

Бренд: Linear Power Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды