L-Acoustics K Series Скачать руководство пользователя

Страница: 76 / 120

Rigging procedures

Rigging a Kara II downll array under a K3 array with KARADOWNK3

Type of deployment

own array

Rigging accessory

KARADOWNK3

Min number of operators

About this task

Reference rigging manuals

This procedure is complementary to the rigging instructions available in the main system rigging manuals.
Refer to

the Kara II owner's manual

for more details.

The following procedure also applies for Kara.

Prerequisite

• Prepare and raise a K3 array. Refer to

Flying an array

with K3-BUMP and K3-BAR

(p.67).

• Prepare an array of three Kara II with 0° inter-

enclosure angles.

• Position the Kara II array under the K3 array.

Make sure the latches on the bottom K3 are in storage position.

Procedure

Take out the four rigging arms on the top Kara II enclosure.

a) Lock the front rigging arms in linking position.

K3 owner's manual (EN) version 1.0

Содержание K Series

























































































































Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды

L-Acoustics K Series, Руководство пользователя

Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды