L-Acoustics K Series Скачать руководство пользователя | Manualshive

Страница: 57 / 120

background image

Inspection and preventive maintenance

Acoustical check

Enclosure check

This feature is available on:

LA4X
LA12X

ENCLOSURE CHECK measures impedance at the reference frequencies for the connected loudspeaker family. The

measured impedance is compared to the expected range allowing for fast detection of loudspeakers presenting circuit

continuity issues.

The results can be used for preliminary diagnosis but cannot replace a comprehensive quality control.

Prerequisite

ENCLOSURE CHECK measurements can only be reliable if the following requirements are met:

Environment and temperature:

• Ambient temperature must be comprised between 0 °C / 32 °F and 40 °C / 104 °F. Ideal temperature is 20 °C /

68 °F.

• Enclosures must be at room temperature. If warm from a recent high level use or recently moved from a cold

environment, let the loudspeakers reach room temperature before starting.

Enclosures:

• Enclosures must be included in the embedded factory preset library.
• Enclosures must be in nominal operating conditions:

• Remove covers or dollies obstructing the loudspeakers or the vents.
• Check for obvious physical damage or air leak: visually inspect the grill, gasket, cabinet, and connector plate

for loose, missing or damaged parts.

Connection:

• Use only 10 m / 30 ft 4 mm² / AWG 11 speaker cables.
• Do not connect enclosures in parallel.

Amplied controllers:

• LA4X must run at least rmware version 1.1.0.
• LA4X load sensors must be calibrated. Refer to the

Load Sensor Calibration Tool

technical bulletin for more

information.

• LA4X must warm up for at least 10 minutes after power up. Do not power off, reboot or switch to standby mode to

avoid resetting the countdown.

• Load a preset corresponding to the connected loudspeaker's family. Presets from the user memories may be used on

condition they are made of presets supported in the embedded factory preset library.

Procedure

1.

Power up the amplied controller. Let LA4X warm up for at least 10 minutes.

2.

Connect the loudspeaker enclosures to the amplied controller.

3.

Load a preset from or built from the embedded library corresponding to the connected loudspeaker family.

4.

On the amplied controller, use the encoder wheel to select

MONITORING & INFO

. Press the OK key or the

encoder wheel to validate.

5.

Use the encoder wheel to select

ENCLOSURE CHECK

.

Beware of sound levels.

Although the sound pressure levels generated for the ENCLOSURE CHECK are moderate, do not stay within

close proximity of the loudspeakers and consider wearing ear protection.

6.

Press the OK key or the encoder wheel to launch the ENCLOSURE CHECK.
The amplied controller generates short sinusoidal signals simultaneously for each connected output.
The amplied controller displays the results for each output.

K3 owner's manual (EN) version 1.0

57

«
...
55
56
57
58
59
...
»

Содержание K Series

























































































































Отзывы:

Нет отзывов

Похожие инструкции для K Series

Бренд: NAD Страницы: 6

Voicesolo FX150

Бренд: TC-Helicon Страницы: 2

ZEB Juke Bar 1500

Бренд: Zebronics Страницы: 5

Бренд: Steren Страницы: 12

Бренд: Ecler essentials Страницы: 10

Бренд: Fender Страницы: 14

Бренд: Emotiva Страницы: 34

XD P329.61 Series

Бренд: XD XCLUSIVE Страницы: 20

Olympica Center

Бренд: Sonus Faber Страницы: 23

Бренд: Tannoy Страницы: 12

Бренд: Revox Страницы: 28

Бренд: Dali Страницы: 38

Бренд: JBL Страницы: 9

Бренд: EAW Страницы: 2

ISB224 v1065-01

Бренд: iLive Страницы: 2

Бренд: Trevi Страницы: 24

Бренд: Atlantic Technology Страницы: 8

Бренд: VR3 Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды