L-Acoustics K Series Скачать руководство пользователя

Страница: 35 / 120

Mechanical safety

Mechanical safety

Flown congurations

The K3 rigging system complies with 2006/42/EC: Machinery Directive. It has been designed following the guidelines

of BGV-C1.
2006/42/EC: Machinery Directive species a safety factor of 4 against the rupture. The own deployments described in

this manual achieve a safety factor of

4 or more

Refer to Soundvision for the safety factor of a specic deployment.
The

safe limit

gives the maximum number of elements for which the safety factor is compliant with the 2006/42/

EC: Machinery Directive, within the use dened in this manual and regardless of the other deployment parameters (site

angles, inter-enclosure angles, etc.).
The

maximum limit

gives the maximum number of elements for which the safety factor can be compliant with the

2006/42/EC: Machinery Directive, when the other deployment parameters provide the best mechanical conditions.
For mixed arrays refer to your Soundvision model.

conguration

rigging accessory

safe limit

maximum limit

K3-BUMP

K3-BUMP + K3-BAR

own

K3-BUMP + 2 K3-BAR + 2 LA-

S LA-RAKMOUNT

18 K3 + 1 LA-RAK II AVB

own and pullback

K3-RIGBAR

K3 + Kara II

conguration

rigging accessory

safe limit

maximum limit

own with a downll

KARADOWNK3

12 K3 + 6 Kara II

18 K3 + 6 Kara II

KS28

conguration

rigging accessory

maximum / safe limit

Flown

KS28-BUMP

Other congurations

For other congurations, respect the recommended maximum limit for optimal stability.

Use safety straps

Always use safety straps on stacked arrays higher than four enclosures.

conguration

rigging accessory

safe limit

maximum limit

Stacked

K3-C K2-JACK

K3 + KS28

conguration

rigging accessory

safe limit

maximum limit

Stacked

K3-TILT + KS28-OUTRIG

5 enclosures

4 K3 + 4 KS28

K3 owner's manual (EN) version 1.0

Содержание K Series

























































































































Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды

L-Acoustics K Series, Руководство пользователя

Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды