L-Acoustics K Series Скачать руководство пользователя | Manualshive

Страница: 119 / 120

background image

Recommendation for speaker cables

Recommendation for speaker cables

Follow the recommended maximum length for loudspeaker cables to ensure minimal SPL attenuation.

Cable quality and resistance

Only use high-quality fully insulated speaker cables made of stranded copper wire.
Use cables with a gauge offering low resistance per unit length and keep the cables as short as possible.

The table below provides the recommended maximum length for loudspeaker cables depending on the cable gauge and

on the impedance load connected to the amplier.

recommended maximum length

cable gauge

8 Ω load

4 Ω load

2.7 Ω load

mm

2

SWG

AWG

m

ft

m

ft

m

ft

2.5

15

13

30

100

15

50

10

33

4

13

11

50

160

25

80

17

53

6

11

9

74

240

37

120

25

80

Use the more detailed L-Acoustics calculation tool to evaluate cable length and gauge based on the type and number of

enclosures connected. The calculation tool is available on our website:

https://www.l-acoustics.com/en/installation/tools/

K3 owner's manual (EN) version 1.0

119

«
...
117
118
119
120
»

Содержание K Series

























































































































Отзывы:

Нет отзывов

Похожие инструкции для K Series

Passport PD-250

Бренд: Fender Страницы: 36

Бренд: Gear Head Страницы: 7

JBL CINEMA SB130

Бренд: Harman Страницы: 16

Бренд: Phoenix Страницы: 27

Бренд: Turbosound Страницы: 13

ULTIMATE EARS BOOM 2

Бренд: Logitech Страницы: 5

Бренд: Fenton Страницы: 16

Бренд: Crest Audio Страницы: 60

Бренд: Soda Trend Страницы: 16

IS-I-IP15 Series

Бренд: Federal Signal Corporation Страницы: 52

Бренд: YORKVILLE Страницы: 10

Бренд: M&S Systems Страницы: 2

Бренд: Harman Страницы: 11

Бренд: Loewe Страницы: 8

Бренд: EAW Страницы: 2

Бренд: Fusion Страницы: 2

Бренд: Vonyx Страницы: 20

Бренд: Preference Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды