manualshive.com logo in svg

Kysor/Warren QILG 06, Руководство по установке и эксплуатации

Поделиться
Скачать
Kysor/Warren QILG 06 Скачать руководство пользователя страница 18

18 

 

 

Bumper, Rub Rail Cap, and Raceway Cover Installation 

1” Bumper 

Install the two-foot length of 1” bumper to the left hand end of the first case in the lineup. To install the 
bumper, hook the lower edge of the bumper to the aluminum retainer. Rotate the bumper up and snap the 
top edge onto the retainer. Install this part as close to the case flat end panel as possible. 
Install the additional case length 1” bumper parts, crossing over the joint of the cases in the lineup and 
trimming the last piece to fit the last case in the lineup. 

 

Rub Rail Cap 

Install the four foot rub rail cap to the left hand of the first case in the lineup. To install the rub rail cap 
hook the lower edge of the cap to the aluminum front rail just above the 1” bumper. On non-glass

 

models, 

rotate the cap toward the case and snap the cap onto the back hook of the aluminum front rail. For glass 
models, rotate the cap toward the case and snap the cap onto the top hook of the aluminum rail. Install this 
part as close to the case flat end panel as possible.

 

 
Install the additional case length rub rail cap parts as close to one another as possible, crossing over the 
joint of the cases in the lineup and overlapping each part where provided. Trim the last part to fit the last 
case in the lineup. 

 

Содержание QILG 06





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды