USER GUIDE
Thank you for purchasing the MULTICELL CHARGER evo.
The MULTICELL CHARGER evo offres excellent all-round performance and supports
most popular rechargeable battery types including NiMH, NiZn, LiIon, LiFe, LiHv.
The high contrast full colour IPS display features a wide viewing angle
which clearly displays detailed option parameters and real-time task progress.
Different batteries can be placed into different slots and operate independently
of each other, and the charger will automatically identify battery types and
choose the appropriate charge settings.
Please read this user manual in detail and follow the instructions carefully
before using your new charger.
Port / Key
Touch Key
IPS Display
Battery Slot
TYPE-C Power Input Port
/Upgrade Port
・
Do not charge a non-rechargeble battery or a battery with damaged surface
insulation.
・
Keep the charger away from humidity and high temperature while charging.
・
Ensure the cooling fan is ventilating properly.
・
Make sure the charge and discharge settings are correct.
・
Incorrect settings may cause dangerous accidents.
・
Do not let the children operate the charger.
・
Do not leave the charger unattended while charging.
Specifcation
Model:
Max. Input Power:
Support Battery Count:
Support Battery Size:
Support Battery Type:
Operating Voltage Range:
Charging Current Range:
Discharging Current Range:
Operation Modes:
Display:
Beep Sound:
Temperature Sensors:
Operating Temperature:
Reverse Polarity Protection:
Overheating Protection:
Overcapacity Protection:
Dimensions:
Weight:
The maximum lateral length of the batteries is 70mm
MULTICELL CHARGER evo
36
W
1 ～ 4
Cylindrical batteries
AAA,AA,
10440
,
10500
,
12500
,
13500
,
14500
,
14650
,
16650
,
17650
,
17670
,
18650
,
18700
20650
,
20700
,
21700
,
22650
,
26650
,
26700
NiMH,NiZn,LiIon,LiFe,LiHv
5 ～ 12
V(Supports QC,PD protocol)
0.1 ～ 3.0
A(Horizontal),
0.1 ～ 1.5
A(Vertical)
0.1 ～ 1.5
A(Horizontal),
0.1 ～ 1.0
A(Vertical)
Charge,Discharge,Storage,Disposal,
Cycle,Activate,Analyse
320
X
240
IPS LCD
Multi-tone
6
0 ～ 40℃
Vertical physical anti-reverse polarity connection and
horizontal anti-reverse polarity connection hardware
Supported
Supported
120
X
92
X
34
mm
About
195
g
Task Setting
Automatic Mode
Using this charger, either four AA or AAA batteries or one
16650 ～ 21700
and one
16650 ～ 26700
battery can be charged, discharged, storaged, cycled, analyzed,
activated and disposal in a variety of combinations.
Connect a Type-C to the MULTICELL CHARGER evo Power input port.
The charger beeps 3 times and start charging in about 5 seconds after installing
batteries in the slots correctly.
Charging status will be displayed in the task
setting screen during charging as shown on
the right.
1.
2.
Available modes depend on battery types.
All the setting parameters are saved upon powering off.
Make sure that parameters are appropriate when using next time.
Caution!!
At this time, short press the middle button to change display information as shown below:
Interface
1
.Task Status
2
.Battery Type
3
.Output Voltage and Current
4
.Charged/Discharged Capacity
5
.Task Operation Time
6
.Voltage Curve
7
.Resistance and Temperature
8
.Charger Status
9
.Task Status Preview Bar
Task progress
Completed
Disconnect
Warning
Charge
Discharge
Disposal
Storage
Cycle
Analyse
Activate
The taskbar shows the status of each task visually, You can switch between
the detailed task pages by using the up and down arrow buttons.
Manual Mode
1.Connect the Type-C connector where
the power supply is connected to the
input terminal of the main unit.
2.After inserting batteries, setting screen
will be shown while beeping 3 times.
Press up and down arrow buttons to
select an item and press the middle
button to change settings.
Battery Type
Task
Charge Setting
NiMH,NiZn,LiIon,LiFe,LiHv
Charge,Discharge,Storage,Disposal,Cycle,Activate,Analyse
0.1 ～ 3.0
A(Horizontal slots),
0.1 ～ 1.5
A(Vertical slots)
The task will automatically begin ten seconds after manual modification is completed.
Cut off
Available modes depend on battery types.