Kyocera ECOSYS P7035cdn Скачать руководство пользователя страница 132

Страница: 132 / 178

2PR

1-6-2

(2) Downloading the firmware from the USB memory

To download data written in a USB memory to the printer, proceed as explained in this section.

CAUTION

Downloading firmware takes several minutes. Do not turn power off during downloading.

Procedure

1. Turn printer power off.
2. Insert the USB memory to the PC's USB

slot.

3. Copy the firmware file to download to the

root directory of the USB memory.

4. Remove the USB memory from the PC's

USB slot.

5. Insert the USB memory into the printer's

USB memory slot.

Figure 1-6-2

6. Turn printer power on.
7. When message display (1) is displayed to

detect firmware in the USB memory.

8. Message display (2) is displayed during

downloading.

9. When message display (3) is displayed to

indicate downloading is finished.

Figure 1-6-3

USB memory

USB memory slot

(2)

(1)

supervisor mode

USB data reading

supervisor mode

Message display

(3)

2PR_1000.000.024

[E1F9]

6
7

3
4

Supplement (Normally: 00)
Classification (Normally: 0)

Product code
2PR: This machine

Checksum

Update history
Build number

Firmware category
10: Engine
30: System
31: System (BROM)

Содержание ECOSYS P7035cdn



















































































































































































Результаты поиска

Содержание ECOSYS P7035cdn

Отзывы:

Похожие инструкции для ECOSYS P7035cdn

Бренды по названию

Популярные бренды

Kyocera ECOSYS P7035cdn, Руководство по обслуживанию

Результаты поиска

Содержание ECOSYS P7035cdn

Отзывы:

Похожие инструкции для ECOSYS P7035cdn

Бренды по названию

Популярные бренды