Kyocera Copystar CS-1635 Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 244

background image

2HA/2HB

2-1-10

(2) Single component developing system

This machine uses the single component developing system, and reversal processing is performed with a + charged
drum and a + charged magnetic toner.
With the single component developing system, toner is electrically charged by friction with the developing sleeve and +
charged when it passes through the magnetic toner blade. The toner that has passed through the magnetic toner blade
forms a uniform layer on the developing sleeve. When the toner layer comes to the location where the developing sleeve
is the nearest to the drum, toner moves between the drum and the developing sleeve by an electric field of the magnetic
pole. Then, when the developing sleeve rotates and passes through the nearest location to the drum, on the portion of the
drum that has been exposed to light, toner is attracted toward the drum by potential difference between the developing
bias and the drum surface and development is performed. On the other hand, on the portion of the drum that has not been
exposed to light, toner is attracted toward the sleeve and development is not performed. When toner comes to an area
where the gap between the drum and the developing sleeve is large, an electric field disappears and toner does not leave
the developing sleeve. Development is complete.

Figure 2-1-13 Single component developing system

North pole

South pole

Developing sleeve

Drum

Magnetic toner blade

Toner

«
...
172
173
174
175
176
...
»

Содержание Copystar CS-1635





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Copystar CS-1635

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 48

Stylus Pro 7900

Бренд: X-Rite Страницы: 36

Бренд: Xerox Страницы: 8

Бренд: GCC Technologies Страницы: 63

Бренд: gCreate Страницы: 9

Бренд: GCC Technologies Страницы: 9

Бренд: GCC Technologies Страницы: 12

Бренд: gCreate Страницы: 21

Бренд: GCC Technologies Страницы: 199

Бренд: Xerox Страницы: 4

Бренд: Lexmark Страницы: 455

Бренд: Xerox Страницы: 15

Бренд: Xerox Страницы: 9

DocuPrint 180 NPS Series

Бренд: Xerox Страницы: 172

Бренд: Xerox Страницы: 11

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды