KYMCO G-Dink 125i, Руководство пользователя

Страница: 399 / 451

11. Electrical System > Self-Diagnosis G-Dink 125i
29
Blinks
Failure
Codes
Fault Description Priority Fault Management
9 P0505 Idle Air Bypass Control Range Fault 2
1-Check idle bypass valve opening is within specs.
(brand new: above 35 degree used: <180 degree)
2.Check throttle body for carbon deposits.
3.Check Idle Throttle Valve for sticking and check
adjustment of screw.
4. Check intake for air leaks
5. Replace the IABV
6. Note-IABV is powered by the battery
10 P0251 Fuel Injector Fault 2
1.Use ohm meter to measure resistance (13.78-15.23
ohms.
2.Check injector wiring and connections.
3.Check battery wiring and connections.
Note-Fuel Injector is powered by battery
11 P0350 Ignition Coil Fault 2
1.Verify ignition is within specs (0.57-0.66 ohms)
2.Check wiring and connections.
3.Check condition of battery wiring and connections.
12 P0230 Fuel Pump Relay Fault 2
1. Check wiring and connections.
2. Listen for relay clicking when ignition is switched on.
13 P0219 Engine Over Speed Condition Fault 2
1. Engine exceeded 10,500 rpm redline.
2. Check belt.
3. Check spark plug. Use resistor plug "R".
14 P1560 Sensor Power Supply Fault 2
1.Use volt meter to check ECU pin 18 (5 volts DC) or
use diagnostic tool (5 volts +/- 0.1 volts).
2.Check voltage difference between pin 16 and pin 18
(5 volts DC).
3.Cylinder head Temperature Sensor, Intake Air
Temperature Sensor, and TPS use the same power
supply. If getting more than three faults, ECU could
be faulty.
15 P0700 Engine RPM/CVT Fault 2
1.If engine exceeds 3250 rpm at idle, ECU will lower
engine idle speed or shut engine down.
2.When start the engine, Do NOT use throttle
3.Check throttle cables and throttle body for sticking
and binding.
4.Check throttle idle voltage (0.68 volts +/- 0.03 volts).
5.Check CVT belt.
16 P0115 Cylinder Head Thermosensor Fault 2
1.Use voltmeter to check resistance (cold 2445.2-
5458.3 ohms).
2.Check wiring and connections for ECU pin 9.
18 P0650 Check Engine Light Fault 3
1.Check bulb (1.7w 12 volt DC).
2.Check ECU wiring and connections pin 4.
21 P0105 Atmosphere Pressure Sensor Fault 2
1.Check sensor voltage (5 volts +/- 0.1 volt).
2.Check ECU wiring and connections pin 8.
3.Use Diagnostic Tool to check pressure (101.3 +/- 3
KPA).
22 P1110 Bank Angle Detector Sensor Fault 2
1.Use KYMCO AFI Diagnostic Tool Check sensor
voltage (3.5~4.7 volts ).
2.Check ECU wiring and connections pin 11.
3.If still getting fault, replace sensor.
23 P0136 O2 Sensor Fault 1
1.Check sensor resistance (Standard: 6.7~9.5
Ω
@20
℃
~30
℃
).
2.Check ECU wiring and connections pin 10.
3.If still getting fault, replace sensor.
24 P0141 O2 Heater Sensor Fault 2
1. Check ECU wiring and connections pin 14.
2. If still getting fault, replace sensor.
25 P0171 Close loop Fault 1
1. Check wiring and connections pins 10 and 14.
2. If still getting fault, the injector probably injected
more fuel or inlet air adnormal. Check if the injector is
cloged, if the valve timing is correct or valve leaking, if
the piston and ring piston is damaged….and so on.