KYMCO Downtown 350i Скачать руководство пользователя страница 524

Страница: 524 / 616

10..Brake System

Downtown 350i

8-46

Caution

If any of the brake line fittings, including the ABS hydraulic unit joint nuts, or the bleed valve

are opened at any time, the air must be bled completely from the brake line.

Do not ride the scooter with air in the brake line, or the ABS could malfunction.

□ The ABS indicator light may light if the tire pressure is incorrect, a non-

recommended tire is installed, or the wheel is deformed. If the indicator light lights, remedy

the problem and clear the service code.

□ When the ABS operates, the ABS makes noise and the rider feels the reaction force on

the brake lever and brake pedal. This is a normal condition. It informs the rider that the ABS

is operating normally.

□ Service codes detected once by the ABS hydraulic unit will be memorized in the ABS

hydraulic unit. Therefore, after maintenance work is finished, be sure to erase the service

codes. Do not erase the service codes during troubleshooting. Wait until all the checks and

repair work is finished to prevent duplication of previous service codes and unnecessary

maintenance work.

□ Before delivering the scooter to the customer, be sure to erase any service codes which

might be stored in the ABS hydraulic unit. Test run the scooter at a speed of more than 6

kph (4 mph) to see that the ABS indicator light does not come on. Finally, test run the

scooter at a speed of more than 30 km/h (20 mph) and brake suddenly to see that the

scooter stops without loss of steering control and the ABS operates normally. (The reaction

force generated is felt in the brake lever and

pedal.) This completes the final inspection.

Содержание Downtown 350i









































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Downtown 350i

Отзывы:

Похожие инструкции для Downtown 350i

Бренды по названию

Популярные бренды

KYMCO Downtown 350i, Руководство по ремонту

Результаты поиска

Содержание Downtown 350i

Отзывы:

Похожие инструкции для Downtown 350i

Бренды по названию

Популярные бренды