background image

4.Engine 

                                                                                                                     

Downtown 350i

 

 

4-85 

 

 

Fit the upper cam chain guide into place. 

 

 

Insert the upper cam chain guide mounting bolt and tighten it to specification with 
an 8 mm Allen socket. 
  

   Item 

Qty 

Thread  

size (mm) 

Torque 

kgf-m 

lb-ft 

Cam chain tensioner pivot 

0.8-1.2 

5.79 - 8.68 

  
Install the oil pump. See the 

Oil Pump

 topic for more information. 

  
Install the starter idle gear, driven gear, flywheel, and the generator cover. See 
the 

A.C. Generator and Starter clutch

 topic. 

  
Install the starter motor. See the 

Starter Motor

 topic for more information. 

  
Install the CVT pulleys and belt. See the 

CVT Installation

 topic for more 

information. 

 

 

Содержание Downtown 350i









































































































































































































































































































































































































































































































































































































































Отзывы: