KYLAND Technology PTS-DR200 Скачать руководство пользователя | Manualshive

Страница: 50 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 48 -

[Figure 3-32] Firmware Screen

Press ‘Download’ to update the new firmware of PTS-DR200 time server. Before do it,
please select upgrade file. After finish this action, you should reboot device and make
the new firmware active. There are 2 types to reboot device. One is turn off power
and then turn on; another is controlled by WEB management system.

The firmware should be published by Official.

3.6.5. SNMP (Optional)

Press ‘SNMP’ on the left navigation bar to manage SNMP feature.
The SNMP screen will be shown as:

[Figure 3-33] SNMP Screen

SNMP management supports to modify agent port and to add or delete V1/V2C and
V3 access parameters. The default agent port of SNMP is 161. The default access
parameter of V1/V2C named ‘public’, it only has read-only permissions. V3 does not
have default value.

Any modifications about SNMP should reboot module to activate it.

3.7.

Management

The WEB management system supports to change user password and reboot device
by WEB.

«
...
48
49
50
51
52
...
»

Содержание PTS-DR200
























































Отзывы:

Нет отзывов

Похожие инструкции для PTS-DR200

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

Octopus G Series

Бренд: TwinMOS Страницы: 29

Бренд: LG Страницы: 11

Бренд: LG Страницы: 8

Бренд: LG Страницы: 22

Бренд: QNAP Страницы: 55

Бренд: ARAID Страницы: 20

Ethernet Network Adapter

Бренд: Sony Страницы: 12

Clie Gear PEGA-WL110

Бренд: Sony Страницы: 80

Бренд: Lava Computer Страницы: 4

Multi-function Communication Interface VC-485

Бренд: Kantech Страницы: 2

301160U - 1TB Ethernet Disk RAID Network Attached...

Бренд: LaCie Страницы: 131

NETBLASTER ZX312T

Бренд: ZNYX Страницы: 10

TotalStorage FAStT600

Бренд: IBM Страницы: 134

GRAND-BDE Series

Бренд: IEI Technology Страницы: 60

GRAND-RE Series

Бренд: IEI Technology Страницы: 46

Бренд: Oki Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды