KYLAND Technology PTS-DR200 Скачать руководство пользователя | Manualshive

Страница: 39 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 37 -

Items

Parameters

Description

IP Mask Address

XXX.XXX.XXX.XXX

Set Subnet mask address for network ports.
ETH0:255.255.255.0
ETH1:255.255.255.0

Interface Mode

Auto

100M-FX FDX

100M-FX HDX

1000M-FX FDX

1000M-FX HDX

Set interface working mode for networks ports.
Auto: 100M/1000M Copper automatic mode;
100M-FX FDX: 100M Optical full duplex mode;
100M-FX HDX: 100M Optical half duplex mode;
1000M-FX FDX: 1000M Optical full duplex mode;
1000M-FX HDX: 1000M Optical half duplex mode.

Press ‘Save’ button to save the current setting when you change setting.

3.5.7. TMS Settings (Optional)

Press ‘TMS’ on the left navigation bar to show TMS setting screen.
Press ‘GOOSE channel’ to select GOOSE publisher and GOOSE subscriber channel.

The GOOSE publisher includes GOOSE-P0/GOOSE-P1 and work on ETH0/ETH1;
The GOOSE subscriber includes GOOSE-S0/GOOSE-S1 and work on ETH0/ETH1.

If select ‘GOOSE-P0’ in GOOSE Channel, the setting screen will be shown as:

[Figure 3-24] GOOSE Publisher Screen (GOOSE-P0)

Table 23 – GOOSE Publisher Setting (GOOSE-P0)

«
...
37
38
39
40
41
...
»

Содержание PTS-DR200
























































Отзывы:

Нет отзывов

Похожие инструкции для PTS-DR200

Wireless Mini PCI Module

Бренд: E-Tech Страницы: 42

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

Бренд: Abocom Страницы: 1

Бренд: Epson Страницы: 71

Бренд: Epson Страницы: 29

Бренд: Epson Страницы: 57

C823312 (Ethernet)

Бренд: Epson Страницы: 76

Junxion Box JB-110b

Бренд: Junxion Страницы: 48

StorTrends 3200n

Бренд: American Megatrends Страницы: 2

StorTrends 3200

Бренд: American Megatrends Страницы: 1

StorTrends 3200i

Бренд: American Megatrends Страницы: 34

StorTrends 3100

Бренд: American Megatrends Страницы: 91

Бренд: G-Technology Страницы: 50

NM2-GXE-2230 Series

Бренд: Lantronix Страницы: 18

Бренд: USR IOT Страницы: 9

Бренд: Planet Networking & Communication Страницы: 2

Бренд: Planet Networking & Communication Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды