KYLAND Technology PTS-DR200 Скачать руководство пользователя | Manualshive

Страница: 14 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 12 -

DR200 time server.

[Figure 3-4] Time Information Screen

3.4.2. Source Status

Press ‘Source Status’ on the left navigation bar to show source status screen.
Press ‘Source Channel’ to select SAT1/IRIG-B1/IRIG-B2/PTP channel.

Please refer to ‘Configuration’ section to set parameters.

Select ‘SAT1’ in Source Channel, the screen will be shown as:

[Figure 3-5] Source Status Screen (SAT1)

Table 5 – Source Status Information (SAT1)

Items

Parameters

Description

Source Status

Normal

Alarm

Show the time source status.
Normal: The time source can use;
Alarm: The time source cannot use.

Satellite Number

0~128

Show how many satellites work together.
Range is between 0 and 128;
Default value is 0.

Antenna Status

Normal

Alarm

Show the antenna status.
Normal: The antenna can use;;
Alarm: The antenna cannot use.

Source Bump

Status

Normal

Alarm

Show the time source bump status.
Normal: The time source has not bump data.
Alarm: The time source has bump data.

Source Priority

1~10

Show the priority for time source. 1 is highest source and 10 is
lowest source. It has 10 levels. System can select best time
sources by source priority.

«
...
12
13
14
15
16
...
»

Содержание PTS-DR200
























































Отзывы:

Нет отзывов

Похожие инструкции для PTS-DR200

Бренд: C&H Technologies Страницы: 1

Бренд: MikroTik Страницы: 9

Бренд: Icom Страницы: 66

Бренд: Quanta Computer Страницы: 13

301138U - Ethernet Disk Mini NAS Server

Бренд: LaCie Страницы: 55

USB CF Host Card REX-CFU1

Бренд: Ratoc Systems Страницы: 21

Бренд: IEI Technology Страницы: 29

LonWorks Communication Module CME-LW01

Бренд: Delta Electronics Страницы: 2

Бренд: Delta Electronics Страницы: 13

DiskStation DS218+

Бренд: Synology Страницы: 20

Бренд: TYAN Страницы: 159

Бренд: Genotech Страницы: 15

LEDI NETWORK TDS V1

Бренд: Gorgy Timing Страницы: 68

LEDI NETWORK TDS GPS RAIL DIN TH 35

Бренд: Gorgy Timing Страницы: 101

Бренд: Atlantis Land Страницы: 11

Gigabit Ethernet Card

Бренд: Atlantis Land Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды