background image

3. Avoid turning for 60 seconds after turning on the

antenna to allow the antenna gyro to inialize
properly.

System Startup (Connected to an IRD Low-speed Data Port)

1. Upon power-up, the system performs a set of

startup routines.

2. The antenna then searches for a TV satellite.

3. Once the antenna finds a satellite, it uses the IRD

data connection to determine if the satellite signal
can be decoded. If the signal can be decoded by
the IRD, the antenna locks onto and tracks the
satellite.

System Startup (Not Connected to an IRD Low-speed Data Port)

1. Upon power-up, the system performs a set of

startup routines. If any errors are detected, the
Status indicator flashes quickly (3-4 times per
second).

2. The antenna then searches for a TV satellite.

During this search, the Status indicator flashes
slowly (1-2 times per second).

3. Once the antenna finds and starts tracking a

satellite, the Status indicator comes on solid.

4. If your TV does not show a clear picture, the

antenna is tracking the wrong satellite. Refer to

Section 3.2.2, “Using the Switchplate for Satellite
Selection”

for instructions on selecting a different

satellite. 

3-2

A Guide to TracVision L2

If Connected to an IRD 
Low-speed Data Port:
As part of the startup process, the
TracVision L2 system will default to
Channel 200, a program directory.
This is the system’s means of
verifying that it has identified and is
tracking the correct satellite.

Once Channel 200 appears, wait at
least another 30 seconds before
changing the channel to ensure
that the system has completed its
startup routine.

Power Button

Sat Select Button

Status Indicator

These features only 
active if the system
is 

NOT connected 

to an IRD low-speed 
data port

Figure 3-2

Switchplate Front Panel

Содержание TracVision L2






































































Отзывы: