KVH Industries TracPhone V11IP Скачать руководство пользователя

Страница: 16 / 55

Follow these steps to detach the antenna from the
pallet and safely rig the antenna for crane
hoisting.

Using a 7/16" socket/ratchet or nut driver,

unlock the three hex latches securing each of

the antenna’s service hatches (see Figure 19).

Then gently lower the hatches. You can now

access the four shipping bolts securing the

antenna’s baseplate to the pallet.

Using a 3/4" socket/ratchet or wrench,

remove the four outer 1/2"-13 bolts securing

the antenna to the pallet (see Figure 20). Do

not remove the four inner bolts that secure

the internal antenna assembly to the

baseplate.

Close both antenna service hatches. Secure

each hatch using the three hex latches.

Secure the crane rigging to the antenna’s four

lift brackets (see Figure 21). Be sure the

rigging and crane are suitably rated to safely

lift the 240 lbs (109 kg) antenna.

Carefully hoist the antenna to its mounting

location.

WARNING

Be sure no personnel stand underneath the

antenna at any time while it is suspended in

the air.

Take protective measures to avoid gouging or

scratching the radome during the rigging

operation.

IMPORTANT!

Hatch (x2)

1/4-turn Hex Latch (x6)

Figure 19: Service Hatches

1/2"-13 Shipping
Bolt (x4)

Do not remove the 4 inner
bolts securing the antenna
assembly to the baseplate!

Figure 20: Shipping Bolts (Antenna Bottom View)

Lift Bracket (x4)

Rope to Prevent
Tipping

Rope

Center of Gravity

Figure 21: Crane Rigging (Example)

Rig and Hoist the Antenna

Содержание TracPhone V11IP
























































Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды

KVH Industries TracPhone V11IP, Руководство по установке

Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды