Kverneland CLC PRO Скачать руководство пользователя

Страница: 76 / 98

Unhitching

Folded position

In order to save space, you may prefer to store the machine with the
chassis folded using the set of storage struts.

Fold back the machine.



Fold up the frame.



Disconnect the electrical cables.



Disconnect the road signals kit connector (if included).



Disconnect the tractor’s hydraulic hoses.



Raise the machine until the clearance is greater than the height of
the storage struts.



Verify that the folding machine parts have been correctly folded
back.

Adjusting the rear struts



While being careful to avoid the protruding edges, access the rear
struts by the back side of the machine.



Remove the spindles (A) to unlock the struts.



Lower the struts in order to move them from the working position
(B) to the storage position (C).



Lock the struts using spindles (A).



Leave via the rear of the machine.

DANGER

No one should stand close to the tractor’s controls while you are
adjusting the struts.

WARNING

•

Never let go of the struts while they are in the locked position.
They could cause injury by falling onto a part of the body.

•

When you are positioned under the machine, be sure to avoid
bumping against any machine parts or protruding edges.

Содержание CLC PRO



































































































Результаты поиска

Содержание CLC PRO

Отзывы:

Похожие инструкции для CLC PRO

Бренды по названию

Популярные бренды

Kverneland CLC PRO, Руководство оператора

Результаты поиска

Содержание CLC PRO

Отзывы:

Похожие инструкции для CLC PRO

Бренды по названию

Популярные бренды