Kval Commander III Скачать руководство пользователя страница 87

Страница: 87 / 168

Powering Operations for the Commander III

3-6

Commander III Operation Manual

Powering Operations for the Commander III

This section describes how to power up and to power down the Commander III.

Powering up the system includes:

• Applying power to the entire system

• Starting the Control Circuit

Powering down the system includes:

• Shutting down the control power

• Removing power from the entire system

How to Power Up the Commander III

Ensure factory air is applied to machine and main air supply is turned on.

Check that all E-Stop buttons are out and safety gate door s are closed.

Note:

A pop-up is displayed on the user screen if an E-Stop is pressed. The pop-up

will indicate which E-Stop has been activated

Make sure the electrical disconnect in the electrical cabinet is turned to the ON

position.

Switch the green

CONTROL TRANS-

FORMER

switch to the ON position. It

should light up.

Push the green

START MACHINE

button

to “boot up” the machine.

Note:

Boot up may take 2 to 3 minutes.

All lights on the status light panel on the

electrical box should be illuminated.

See

“Description of the Six Light Panel” on
page 5-12

Note:

If a status light does not turn on during

the power up process, see the Trouble-
shooting Chapter in the Service Manual.

Содержание Commander III









































































































































































Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды

Kval Commander III, Руководство по эксплуатации

Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды