manualshive.com logo in svg

Kval 994-X, Руководство по эксплуатации

Поделиться
Скачать
Kval 994-X Скачать руководство пользователя страница 90

Operator Controls

KVAL 994-X Operation Manual

4-8 

Operator Controls

The operator controls the machine with the:

• Operator’s Station.
• Machine Control.
• Jamb / Door Clamp Foot Pedal.

Operator’s Station 

The 

Operator’s Station 

contains a touch screen that allows communication between the operator 

and the machine. Door cutting parameters can be stored and retrieved by one touch. The station 

also includes management functions such as daily and lifetime totals. 

See “Description of User 

Interface Screens” on page 2-8 

and 

See “Quick Start” on page 2-3

 for more information.

FIGURE 4-17.

Operator’s Stations with touch Screen Interface

The Operator’s Station can be placed at different locations as per customer requirements. Above are 

examples of an Operator’s Station attached to the machine and a centrally located station with a Handler 

interface.

Controls:

•   Emergency Stop
•  Start “boot-up” and 

Stop

•  Lock Out ability to 

change programs

•  Turn ON or OFF Control 

Transformer

Содержание 994-X



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды