Kval 994-X Скачать руководство пользователя страница 67

Страница: 67 / 130

Check Specifications of the Front Section

3-7

KVAL 994-X Operation Manual

Check Specifications of the Front Section

Follow these steps in this section to verify the result of the cut and, if necessary, adjust the

machine.

Enter a Positive or Negative Number?

Determine when to enter a positive of negative number by using your

Left Hand

. Use the cut on

the door as a reference. Hold out the left hand with the first finger pointed at the door, second fin

ger and thumb at right angle to each other. The first finger represents the

positive

direction of the

‘Z” axis, the thumb represents the

positive

direction of the ‘Y” axis, then second finger represents

the

positive

the direction of the ‘X’ axis.

Y-

X Axis Positive

movement

Z Axis Positive

movement

Y Axis Positive

movement

Z -

X +

Y +

Z +

X -

Either Front Section or Back Section Cuts

Содержание 994-X



































































































































Результаты поиска

Содержание 994-X

Отзывы:

Kval 994-X, Руководство по эксплуатации, Страница: 67 / 130

Результаты поиска

Содержание 994-X

Отзывы: