Kval 994-X Скачать руководство пользователя страница 35

Страница: 35 / 130

Powering Operations for the 994-X

2-5

KVAL 994-X Operation Manual

Powering Operations for the 994-X

This section describes how to power up and power down the

994-X

Powering up the system includes:

• Applying power to the entire system.
• Starting the Control Circuit.

Powering down the system includes:

• Shutting down the control power.
• Removing power from the entire system.

How to Power Up the 994-X

Ensure that factory air is applied to machine and main air supply is turned on.

Check that all E-Stop buttons are out and safety gate doors are closed.

Note:

A pop-up is displayed on the user screen if an E-Stop is pressed. The pop-up

will indicate which E-Stop has been activated.

Make sure the electrical disconnect in the electrical cabinet is turned to the ON posi

tion.

Switch the green

Control Circuit

switch to the ON position. It should light up.

Push the green

Start Machine

button to ‘boot up’ the machine.

Note:

Boot up may take 2 to 3 minutes.

Control Circuit

Start

Note:

Some control panels may have a different orientation of

the buttons.

All lights on the status light panel on the electrical

box should be illuminated.

See “Description of the

Six Light Panel” on page 4-33

Note:

If a status light does not turn on during the

power up process, see the

994-X Service Manual

for assistance in identifying the issue.

Содержание 994-X



































































































































Результаты поиска

Содержание 994-X

Отзывы:

Бренды по названию

Популярные бренды

Kval 994-X, Руководство по эксплуатации

Результаты поиска

Содержание 994-X

Отзывы:

Бренды по названию

Популярные бренды