Kval 990FX страница 32 Скачать руководство пользователя

Страница: 32 / 96

Initial Powering Operations for the 990-FX Line

KVAL 990-FX Operation Manual

2-2

Initial Powering Operations for the 990-FX Line

This section describes how to power up and to power down the

990-FX

Line.

Powering up the system includes:

• Applying power to the entire system
• Starting the Control Circuit

Powering down the system includes:

• Shutting down the control power
• Removing power from the entire system

How to Power Up the Line

Ensure factory air is applied to each machine and main air supply is turned on.

Check that all E-Stop buttons are out and safety gates are closed.

Note:

A pop-up is displayed on the user screen if an E-Stop is pressed. The pop-up will indicate which

E-Stop has been activated

Make sure the electrical disconnect each electrical

cabinet is turned to the ON position.

Switch the green

Control Power

switches to the ON positions. They should light up.

Push the green

Start Machine

buttons to “boot up” the machines.

Note:

Boot up may take 2 to 3 minutes.

Control Power Switch

Start Machine

Содержание 990FX

































































































Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды

Kval 990FX, Руководство по эксплуатации

Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды