background image

VHD5000 · Introduction 

Introduction

Active control and amplification unit specifically designed in conjunction with VHD5000S for powering the VHD5 loudspeaker 
system. The VHD5000 is equipped with many features for easy large scale speaker system use. It features all signal processing, 
crossover and speaker system protection. All signal processing is executed with KV2 Audio Super Audio Analog circuitry and 
utilize KV2's industry leading 20MHz sampling for on board time alignment and phase correction for maximum audio quality. 
The VHD5000 is equipped with multiple delay lines, wideband delay line for VHD5 system delay, fill output delay and two low 
frequency delay lines for subwoofers.

The Main input, fill output and subwoofer outputs are equipped with phase reverse and set level features.

The VHD5000 input is "Line Driver Ready", it has an input signal impedance selector switch, (10kOhm and 120Ohm) to match up 
low impedance signal source when driving long signal cables. In most cases it would be advisable to use a VHD LD4 Line Driver 
in addition at the mixer outputs, to ensure that the line to the amplifier is driven correctly and the signal integrity maintained.

The VHD5000 also features long distance eq, high frequency recovery and a signal generator. The amplifier is equipped with 
multiple network possibilities for easy remote control operation from networked amplifiers or website applications.

The amplifier compliment inside the VHD5000 is as follows:

High Frequency 1 - 300-watt, Class AB Push-Pull low IM Mosfet design with transformer balanced output.
High Frequency 2 - 600-watt, High Efficiency, High power bandwidth, low intermodulation design.
Mid Frequency - 1500-watt, High Efficiency, High Power Bandwidth, low intermodulation design.

VHD5000 - part number KVV 987 334 (230V)

Application

Specifically designed as the amplification and control for the 1xMid/Hi VHD5.0 part loudspeaker systems with adjacent 
VHD5000S in a rack mount module

• 

Large scale Portable PA

• 

Fixed installations

• 

Large clubs

177

481.4

177

431.6

177

451.9

Rear Panel:

Front Panel:

Side Panel:

FOR YOUR SAFETY, READ THE IMPORTANT 
PRECAUTIONS SECTION AS WELL AS THE INPUT, 
OUTPUT AND POWER CONNECTION SECTIONS 
OF THIS MANUAL.

4

VHD5000 ·  I

ntr

oduc

tion

Содержание KVV 987 334







































Отзывы: