KUST Elektronik PT5040 Скачать руководство пользователя страница 36

Страница: 36 / 87

I/O
















PT5040 Operation Manual Chapter 6 Introduction to [SYSTEM]



Off Turn off the password function. When user turns on or unlocks the instrument, it is

not required to input password.

Note: When turning off the password function, it is required to input the password.



Modify This key is used to modify the password. The instrument will prompt user to input

old password, new password and new password again in turn. (Press ESC to exit

from modifying password.)

Note: Only numbers can be used as password.

Language

Move the cursor to this zone, following soft keys will be displayed.

中文

Choose Chinese as the display and operation language.

English Choose English as the display and operation language.

Theme



RoyalBlue



Seagreen



Steelblue



Indianred

Date

Date can be set in this zone. The display format is like 2012/06/06. Move the cursor to this zone,

following soft keys can be used.

They are soft keys used to adjust date by 1 day.



Note: The date can be directly input by numeric keys. In the process of inputting

numbers, soft keys are not available. User can press ENTER to terminate inputting (In the

state of inputting, if it is required to exit from modifying, press ESC.).

Time

Time can be set in this zone. The display format is like 06:08:28. Move the cursor to this zone,

following soft keys can be used.

They are soft keys used to adjust time by 1.



Note: The time can be directly input by numeric keys. In the process of inputting

numbers, soft keys are not available. User can press ENTER to terminate inputting (In the

state of inputting, if it is required to exit from modifying, press ESC.).

Interface

In this page, information about RS232 interface, USB interface (USBTMC or USBCDC),

6-14

Содержание PT5040
























































































Результаты поиска

Содержание PT5040

Отзывы:

Бренды по названию

Популярные бренды

KUST Elektronik PT5040, Руководство по эксплуатации

Результаты поиска

Содержание PT5040

Отзывы:

Бренды по названию

Популярные бренды