Küppersbusch KD 9760.0 GE, Инструкция по использованию и установке

Страница: 6 / 7

18
EN
G
1 150/ 120 mm reduction.
1 Anti-recoil valve.
2 Support for tubecover.
2 Wall support.
6 Wall plugs (Ø8 x 40).
6 Long bolts (Ø5 x 45).
4 Wall plugs (Ø6 x 30).
4 Long bolts (Ø4 x 30).
2 Ø6,4 x Ø18, washers.
2 Ø6,4 x Ø12, washers.
2 Screws (Ø3,9 x 19).
4 Screws M4 x 12.
2 Clips.
Fig. 1 (Page 19)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
14 are complied with.
To obtain optimum performance, the external
conduct must not be more than FOUR
METRES long, have no more than two 90°
angles and its diameter must be at least Ø120.
1) Trace and drill the points for fitting the wall
plugs onto the wall (P) (Ø8 x 40) and (J) (Ø6 x
30).
2) Attach the Supports (O) to the wall using the
long bolts (Q) (Ø5 x 45) and the support (H)
with the long bolts (I) (Ø4 x 30), as in figure 1.
3) Hang the kitchen hood onto the mounted
supports (O). Straighten the appliance by
tightening the long bolts (L) (M4 x 12).
4) Press the glass upwards and carefully open
downwards until the end stop. Remove the
metal filters.
5) Trace the location of the wall plugs (R) (Ø8
x 40), through the inside of the kitchen hood.
6) Bring the glass back upwards to its initial
position and carefully press for fitting it. Take
the kitchen hood off.
7) Drill into the wall and fit the wall plugs (R)
(Ø8 x 40).
8) Hang the kitchen hood; tighten the screws
(M) (M4 x 12). Press the glass upwards and
carefully open downwards until the end stop.
Tighten the long bolts (S) (Ø5 x 45) with the
washers (T) (Ø6,4 x Ø18).
9) Place the metal filters. Bring the glass back
upwards to its initial position and carefully
press for fitting it.
10) Mount the tubecovers, attaching the lower
one to the support (H) as per the detail in figure
1. Lift the upper tubecover up to the desired
height and mark its shape on the wall. Remove
the tubecovers.
11) Place the clips (F) to the support (C).
12) Centre the support (C) around the shape
marked; trace and drill the fixing points for the
wall plugs (E) (Ø6 x 30). Attach the support (C)
with the long bolts (D) (Ø4 x 30).
13) Fit the parst (A+B) if the inner tube (not
supplied) is Ø120.
14) Attach the inner tube with a clamp (not
supplied) to (B) or on to the motor's air outlet
vent as the case may be.
15) Once the inner tube is fitted, fit the lower
tubecover around the extractor fan outlet and
attach the upper tubecover with the screws (G)
(Ø3,9 x 19).
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life of
between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They must
be replaced once their useful life comes to an
end.
Fig. 4 (Page 19)
1) Press the glass upwards and carefully open
downwards until the end stop . Remove the
metal filters.
2) Put the filters into the lateral draught section
of the motor making the holes in the filters
match up (A11) with the pivots (A12) of the
motor carcass.
3) Place the metal filters. Bring the glass back
upwards to its initial position and carefully
press for fitting it.
4) Remove the tubecovers (H). Fit the support
(J) in the diffuser (C). Mount the connector
Ø150 (L) in the diffuser base.
5) Use the wall plugs and the previously
installed upper tubecover's support (I) long
bolts (D) (Ø4 x 30) to fix diffuser into the wall
(C).
6) Connect the connector base (L) to the motor
exit via the inner tube (not supplied). Use
clamps (Not supplied). Fit the tubecovers (H)
again.
Active charcoal filters (Optional)
Installation
Accesories supplied