KUHN GMD 3150 TL CE Скачать руководство пользователя страница 63

Страница: 63 / 68

10. - Maintenance and storage

GMD 3150/3550/4050 TL CE

7N136AGB-A

Disk mower

10.5 Storage



At the end of each season

- Clean the machine thoroughly.
- Drain all gearboxes and refill with new oil (see

"Lubrication" chapter).

- Touch up any areas of damaged paintwork.
- Put the machine under cover in a dry place.
- Inspect and replace worn knives and bolts (See

section: Inspection of knives and securing
elements).

- Depressurize all hydraulic functions.



At the start of each season

- Pressurize the hydraulic circuit.
- Check the condition of the friction slip clutch (see

"Secondary pto shaft" chapter).

- Inspect and replace worn knives and bolts (See

chapter: Inspection of knives and securing
elements).

- Check that all nuts and bolts are sufficiently

tightened.

- Re-read the operators' manual.
- Make sure that all protection devices are in place

and in good condition.

- Check tyre pressure.



Toolbox

The toolbox is located on the left side of the
machine. The following items are included in the
toolbox:

- 18 mm box wrench
- 6 each left and right turning blades and hardware
- 10 mm allen wrench
- 4 disc spacers

Содержание GMD 3150 TL CE





































































Результаты поиска

Содержание GMD 3150 TL CE

Отзывы:

Похожие инструкции для GMD 3150 TL CE

Бренды по названию

Популярные бренды

KUHN GMD 3150 TL CE, Руководство оператора

Результаты поиска

Содержание GMD 3150 TL CE

Отзывы:

Похожие инструкции для GMD 3150 TL CE

Бренды по названию

Популярные бренды