KUHN ATHENOR 6070 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 98

background image

Instructions for work

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

65

10. Straw blowing

Select the blower speed for straw blowing: 540 min

-1

.

- Start up the tractor PTO and bring the engine up to

nominal speed.

- Switch the tractor's hydraulic distributor to continuous

pumping.

- Position the distribution chute or the swivel chute

(optional equipment) so that the straw is sprayed
where you want it.

- Start the bale separator by engaging it until the light

indicator comes on.

- To distribute the product, start the conveyor moving

forward. Adjust the conveyor speed according to the
type of straw. The conveyor speed is adjusted from
the control unit. It will depend on several things: how
fast the tractor is moving, the rate of distribution and
the type of product.

- Use the hook to keep the bale in contact with the

separator.

- When the distribution is finished:

• Retract the arm and hook as far as they will go.
• Stop the conveyor and disengage the beater bar.
• Disengage the bale separator.

- Put the tractor's distributor lever back to neutral,

disengage the PTO and switch off the engine.

In certain cases, the first part of rectangular
bales tends to shoot upwards at the start of straw
blowing. The guides push the product towards
the back of the machine. For this reason it is
important not to stop the conveyor and to let the
product drop naturally to the back.

«
...
65
66
67
68
69
...
»

Содержание ATHENOR 6070



































































































Отзывы:

Нет отзывов

Похожие инструкции для ATHENOR 6070

Бренд: Hagie Страницы: 61

Бренд: JackJaw Страницы: 2

Бренд: Navman Страницы: 17

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Danelec Страницы: 67

Бренд: PASCO Страницы: 30

Бренд: Accurate Technology Страницы: 10

Бренд: Gage Bilt Страницы: 28

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренд: Össur Страницы: 92

Бренд: Össur Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды