manualshive.com logo in svg

Kubota WSM L3540-II, Руководство по ремонту, Страница: 568 / 672

Поделиться
Скачать
Kubota WSM L3540-II Скачать руководство пользователя страница 568

ELECTRICAL SYSTEM

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

9-S35

[4] ELECTRIC CONTROL SYSTEM

 CAUTION

• For checking of electric circuit, use the circuit tester and test function of electronic instrument panel

(Refer to "[2] TESTING, SETTING AND ADJUSTING BY ELECTRONIC INSTRUMENT PANEL
(INTELLIPANEL) of "4. CHECKING AND ADJUSTING" in this section).

• As for the checking of sensors, switches and solenoid, do the following order; check the battery, fuse

and grounding line first, check by the test function of electronic instrument panel next, and check the
connectors of panel or electronic control unit. If any problem is found there, check individual sensors,
switches or solenoids to see whether the problem exists at the sensor, switch and solenoid side or at the
wire harness side.

• When the normal function is restored as the result of replacement of the part which is suspected to see

that the trouble is regenerated.
IMPORTANT

• When connecting or disconnecting the connector for the purpose of checking, be sure to turn OFF the

main switch before hand. Moreover, pay attention not to allow the terminal to come in contact with other
terminal or chassis while checking.

• When applying the test pin of the tester to the connector terminals, use care not to damage to the

connector terminal.

9Y1211167ELS0031US0

(1)  Checking Fuse and Connector

Checking Fuse

1. Check the fuse.
2. If any of the fuses is blown, replace it with the one having same

capacity.

IMPORTANT

• If a fuse is blown, check the cause and be sure to replace it

with the one having same capacity.

9Y1211167ELS0032US0

Fuse No.

Capacity (A)

Protected circuit

(1)

5

Panel

(2)

20

Hazard

(3)

5

T/M controller 1 [GST/HST type]

(4)

10

Dome lamp

(5)

20

Aircon blower

(6)

10

Radio cassette

(7)

30

Starter relay

(8)

5

Lamp relay

(9)

10

Power outlet

(10)

30

3pin socket

(11)

5

Key stop

(12)

7.5

Alternator

(13)

10

T/M controller 2

(14)

20

Cigar lighter

(15)

7.5

Aircon compressor

(16)

30

Wiper

(17)

20

Flasher

(18)

25

Head light

(19)

15

Work light

(20)

30

Defogger

(21)

45

Head light

(22)

Slow blow

Check circuit against wrong battery

KiSC issued 02, 2015 A 

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов