manualshive.com logo in svg

Kubota WSM L3540-II, Руководство по ремонту, Страница: 400 / 672

Поделиться
Скачать
Kubota WSM L3540-II Скачать руководство пользователя страница 400

FRONT AXLE

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

6-M1

1. STRUCTURE

[1] 4WD TYPE

for L3540-II

The front axle of the 4WD is constructed as shown above. Power is transmitted from the transmission through the

propeller shaft (17) and to the spiral bevel pinion shaft (14), then to the spiral bevel gear (13) after that to the
differential gear.

The power through the differential is transmitted to the differential yoke shaft (19), and to the bevel gear shaft (21)

in the bevel gear case (6).

The revolution is greatly reduced by the bevel gears (23), (4), then the power is transmitted to the axle (1).
The differential system allows each wheel to rotate at a different speed to make turning easier.

9Y1211167FAM0001US0

(1) Axle
(2) Collar
(3) Axle Flange
(4) Bevel Gear
(5) Bevel Gear
(6) Bevel Gear Case

(7) Bevel Gear
(8) Differential Side Gear
(9) Differential Pinion
(10) Pinion Shaft
(11) Collar
(12) Front Axle Bracket, Front

(13) Spiral Bevel Gear
(14) Spiral Bevel Pinion Shaft
(15) Front Axle Bracket, Rear
(16) Coupling
(17) Propeller Shaft
(18) Differential Case

(19) Differential Yoke Shaft
(20) Front Axle Case
(21) Bevel Gear Shaft
(22) Front Gear Case
(23) Bevel Gear

KiSC issued 02, 2015 A 

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов