Kubota WSM L3540-II Скачать руководство пользователя

Страница: 283 / 672

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-S37

Checking Charge Relief Pressure

CAUTION

• When checking, park the machine on flat ground, apply the

parking brake.
NOTE

• Use a new transmission oil filter.

1. Remove the hex. socket head plug (GPF 3/8) from charge

pressure check port (1).

2. Assemble adaptor

(07916-50371) and thread joint

(07916-50341) with the gasket between them.

3. Install the assembled adaptor

and thread joint to charge

pressure check port (1).

4. Install the cable, thread joint in relief valve set pressure tester

and low pressure gauge to threaded joint in order.

5. Place the range gear shift lever in neutral.
6. Run the engine at rated speed.
7. Release the HST pedal to set in neutral, and measure the

charge pressure.

8. If the measurement is not within the factory specifications,

check charge relief valve or adjust with adjusting shim.

NOTE

• Adjusting shim is located on between spring guide and

plug (7).

(Reference)

• Thickness of adjusting shim: 0.2 mm (0.0082 in.)
• Pressure charge per 0.2 mm (0.008 in.) of shim:

Approx. 50 kPa (0.51 kgf/cm

, 7.3 psi)

• Pressure change per 0.5 mm (0.02 in.) of shim:

Approx. 125 kPa (1.27 kgf/cm

, 18.1 psi)

NOTE

• Low pressure gauge is 5 MPa (50 kgf/cm

, 711 psi) full

scale.

9Y1211167TRS0030US0

Charge pressure
(Oil temperature at 50 to
60 °C (122 to 140 °F))

Factory specification

2.35 to 2.55 MPa
24.0 to 26.0 kgf/cm

341 to 369 psi

(1) Charge Pressure Check Port
(2) Poppet
(3) Spring
(4) Shim
(5) Holder

(6) O-ring
(7) Plug

Forward Side

R: Reverse Side

KiSC issued 02, 2015 A

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание WSM L3540-II

Отзывы:

Похожие инструкции для WSM L3540-II

Бренды по названию

Популярные бренды

Kubota WSM L3540-II, Руководство по ремонту

Результаты поиска

Содержание WSM L3540-II

Отзывы:

Похожие инструкции для WSM L3540-II

Бренды по названию

Популярные бренды