Kubota VS 220 Скачать руководство пользователя страница 79

Страница: 79 / 154

To be done before spreading

The slide rule

The slide rule that has been supplied with your spreader is used for

determining the flowrate in lbs per minute (step 1-4).

You use it for:

•

finding the setting of the regulating rod on the spreading chart

decal (steps 5 and 6).

•

and for performing a calibration test.
(step 7 is for the disc spreaders)

Metric and Imperial

On the front of the slide rule are metric units and on the back imperial

units.

The slide rule consists of three parts:

•

Transparent ruler with hairline; can slide along outer case.

•

Outer case with 6 steps to determine the setting.

•

Sliding ruler with the values lbs/acre and lbs/min on the imperial

side; can slide to the left or right.

Determining the flowrate (lbs/min.)

with the slide rule

Select step by step the following values on the slide rule:

1. Working width (ft)



Set the hairline of the ruler on your working width; in this example

49 feet.

2. Application rate (lbs/acre)



Push the ruler at the left slot to the right

Outer case Imperial side

Ruler with hairline

Ruler

Slot

Hairline on working width 49 feet

Push ruler to the right

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды