Kubota VS 220 Скачать руководство пользователя

Страница: 61 / 154

Assembly instruction

Fitting the border-spreading

plate

Mounting border-spreading plate support frame

If the machine is supplied with the border-spreading plate, first mount

the support frame on the right-hand side of the spreading unit.

Possibly in combination with the other accessories which are fitted to

the spreading unit.



On the right-hand side of the spreading unit remove the bolt of the

spreading plate and the two bolts of the cap.



Fit the support frame to the spreading unit with the two supplied

bolts on the cap.



Put the two spacers on the hole of the spreading plate.



Push the longer bolt from the inside through the cap, spreading

plate, washers and the top arm of the support frame.



Take care that the bolt head drops into the hexagon of the
cap before you tighten the nut!



Tighten the nut on the bolt with 11 ft.lbs.

Border-spreading plate assembly

The large surface area of the border spreading plate is the reason for

its great susceptibility to changes in temperature. A rigid assembly will

upset the flat shape during expansion.

Therefore the plate must be able to move to some degree on the

fastening points. That way distortion of the border-spreading plate is

prevented.



Fit the two clamping pins into the two top tubes of the border-

spreading plate frame.



Mount the plate onto the frame with the bolt heads and the washers

on the plate side, the nuts on the frame.



Tighten the nuts until the washer rests on the plate without play.



Take care that the plate can be shifted between washer and
frame!

This prevents the buckling of the spreading plate.

Fitting the storage hook

A bracket is fitted on the hopper to store the spreading plate, if not in

use.



Turn the border-spreading plate with the lug to the top and the

pipes pointing to the back.



Push the bottom pipe into the bottom holder pipe.



Secure the lock clip.



Hook the lug onto the hopper hook and secure them with the clip.



Press the hook against the hopper.



Mark the two holes on the hopper.

Support frame for border-spreading plate

2 distance spacers

Placing longer bolt with the head in the

hexagon of the cap

Support frame for border-spreading plate

Border spreading plate

Frame of the border-spreading plate

Clamping pins

Lug with

hook

Bottom holder pipe

Drill two holes

Lock clip

7/16”

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды